Just How to Install a Bathtub Yourself
Just How to Install a Bathtub Yourself
Blog Article
The publisher is making a few good annotation about Installing A Bathtub overall in the article followed below.
Installing a tub isn't exactly brain surgery, yet it does need strong plumbing, carpentry, and also sometimes, tiling abilities. Changing an old tub with a brand-new one is additionally a moderately hard job. If the old bathtub is easily obtainable, the project can relocate quickly; if you need to open a wall surface to remove the old bathtub and position the brand-new bath tub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will require an assistant to move out the old tub and also set in the new one. Make certain you have qualified on your own for the work and are comfortable trying it. As opposed to hiring a specialist to take control of a halfway-completed project, it is much better to take into consideration using one before you begin. Possibilities are you might need a professional plumber to make tube connections.
This write-up will certainly help you set up a brand-new bath tub in your washroom if you have actually already purchased a brand-new bathtub and also don't need to alter the plan of your previous water pipelines.
Your tools and material checklist must consist of the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you should do is detach the supply of water. After doing so, switch on the faucets to drain pipes any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly bothersome as a result of the limited accessibility that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a fabric ready for the remaining water that will originate from the pipelines. When the supply pipes have been removed, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning during this procedure. When the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Before going on to fit the brand-new taps, compare the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap and also the various other end provides a link to the existing supply pipes.
If you require to fit a monobloc, then you will call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin making certain that the washers remain in location in between the faucet and the sink. Safeguard the faucet in place with the producer given backnut. When the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap connectors. The former kind should be linked to the faucet ends initially, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Mounting the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wood boards are useful in equally spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 small factors.
The next goal is to make certain that the bathtub is leveled all round. This can be attained by checking the spirit level and also adjusting the feet on the tub till the spirit level checks out degree.
To install faucets, fit the bottom of the outermost versatile faucet connector to the ideal supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Activate the water supply as well as examine all joints as well as brand-new pipework for leakages and tighten them if required. Load the bath tub and likewise examine the overflow outlet and the typical electrical outlet for leakages.
Finally, repair the bathroom paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub ought to wait till the bathtub has been made use of at least once as this will certainly resolve it into its final setting.
Planning for the Installation
First of all, the sustaining structure supplied with the bath must be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the adaptable tap connectors to the bottom of the two taps utilizing 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you utilize all of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath should currently be ready to be fitted in its final position.
Tiling Around the Bathtub
In the location where the bathroom fulfills the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to crack an inflexible seal, triggering the water to penetrate the wall in between the bathroom and the tiling, leading to difficulties with moisture and feasible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your components as well as fittings. They are marketed in tubes and also cartridges, as well as are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of soaked paper or soft rope. Keep in mind to always fill the bath tub with water prior to sealing, to allow for the activity experienced when the tub remains in use. The sealant can crack rather early if you do not take into account this activity before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly available on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or water resistant glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm certainly very focused on Tools You Need to Install a New Bathtub and I'm hoping you enjoyed our article. Sharing is nice. Helping others is fun. Thanks a lot for your time. Visit again soon.
Book Inspection
Report this page